All Categories
XTOOL EZ300 PRO With 5 Systems Diagnosis Tool
$258.00Free Shipping
$258.00Free Shipping
$289.00
①MicroUSB：Battery charge or data synchronization with PC
②DB15 Port：Supports wired connection with car by the cable
③Power Button: Power on or power off
EZ300PRO Technical Parameters:
Operating System: Android
Processor：Quad-core 1.6GHz Processor
Memory: 1G RAM，16G FLASH
Display: 7.0 inch touch screen with 1024×600 resolution
Sensors: Gravity Sensor，Ambient Light Sensor
Audio Input/Output: Microphone, Dual Speakers, 4-Band 3.5 mm stereo/standard headset jack
Power and Battery: 4000mAh, 3.7V lithium-polymer battery
Power Voltage: 5V
Power Consumption: 8W
Operating Temperature: -20 to 50℃(-4 to 126℉)
Humidity: <90%
Dimension (L*W*H): 218*150*29mm
Vehicle Connection Diagnosis:
Vehicle Connection Test:
Wired Connection ①→②→③→④
a. Connect cables and EZ300PRO in following order: ①→②→③→④
b. Switch on the ignition and turn on EZ300PRO tablet, then tap on EZ300PRO application to test vehicles. (Shown as follows)
① EZ300PRO Mainframe ② Main Test Cable ③ OBDⅡ-16 ④ Vehicle
Precautions Before Use:
1.The vehicle power supply has to meet the normal voltage limits DC4.8V---5V.
2.When pull and plug test wire harness, users should pinch the front-end
of the wire harness to pull and plug, not pull the middle section of
the wire harness. Users should check the corresponding direction of the
port and plug in horizontally when they plug the wire harness, instead
of inserting in an oblique way, which may damage the terminal.
3. When taking some special functions tests, users are required to
operate the device according to operating instructions. For vehicle, it
has to strictly meet the requirements, for example, the conditions that
some vehicle models need to be reached are as follows: engine
temperature 80℃/105℃, turn off the loads (such as headlights,
air-conditioner, etc.), put accelerator pedal in released position, etc.
4. The ECU for Chinese domestic vehicle models are relatively
disorderly, so when users meet conditions, such as the car can not be
tested or the test data is wrong, they should consider whether the
selected menu corresponds to the tested electronic control system, or
they can find the car ECU and select the right menu according to the
model number on the ECU label.
5. If users can not find the tested vehicle model or electronic control
system in EZ300PRO test menu, they may need to update the software or
consult Xtool technical service department
6. Banned to have connection test by using harness not from Xtool to avoid unnecessary losses.
7. Banned to power off directly in the communication between EZ300PRO
and vehicle. Users should cancel the task and return to the main
interface, then power off.
8. The device should be put and lifted slightly to avoid collision when
using EZ300PRO. When click the screen, touch it gently to guarantee the
service life of the touch screen.
9. During long period of non-use, please disconnect the power and turn it off.
Menu Options:
1.After EZ300PRO tablet connected to vehicle via main cable, diagnosis
can be performed now. The diagnostic interface comes up as below.
2. Users can choose menu based on their actual needs: selection for
Europe means entering European cars menu, selection for Asia means
entering Asian cars menu, selection for America means entering American
cars menu, selection for China means entering Chinese cars menu. Users
also can input vehicle model to search.
Test Functions:
Take Volkswagen car for example, select Diagnosis, then select Europe
Car, users can see Volkswagen’s logo. If the logo has not been seen,
please swipe up and down or enter the car model to research.
Different vehicles have slight different menus.
Common main function menu includes the following options:
Read ECU:
this function is to read ECU version information, which is the
equivalent of “System Identification” or “System Information” in some
electronic
control systems, all mean to read ECU related software and hardware
versions, models and production date of diesel engine, part number,
etc. It is convenient for us to make record in the maintenance process,
and it also makes later date feedback and management easier.
Read DTCs:
read trouble codes stored in ECU.
Select Read Trouble Codes to read trouble codes stored in ECU. Screen
will show the trouble code and its definition when read the
trouble codes,shown as below.
Tip: In the process of diagnosis, if the device shows “System is OK” or “No Trouble Code”, it means there is no related trouble code
stored in ECU or some troubles are not under the control of ECU, most of
these troubles are mechanical system troubles or executive
circuit troubles, it is also possible that signal of the sensor may bias within limits, which can be judged in Live Data.
Clear DTCs:
Return to the previous step, select Clear DTCs to clear current and
historical trouble codes memory in ECU. Performing this function will
clear all thecurrent and historical trouble codes. Make sure whether the
trouble codes have been recorded before clearing, shown as below.
Click YES to make clear confirmation, if the communication is normal, it
will show “Trouble Codes Successfully Cleared” or “Trouble Codes
Cleared”. Generally, users need re-read trouble codes after cleaning
them to confirm whether the trouble codes have been cleared.
Suggestion:
users should better not to clear trouble codes, we need record the
trouble details after reading code, which is provided as reference for
maintenance.
After dealing with troubles, there will be no trouble code when we re-read.
Read Live Data:
that is to read the parameters of running engine, such as oil pressure,
temperature, engine speed, fuel oil temperature, coolant temperature,
intake air temperature, etc. Based on these parameters, we can judge
directly where the problem lies, which helps to narrow the scope
in maintenance. For some vehicles, during their actual operation, the
problems such as performance characteristics offset, sensitivity
reduction,
can be judged in live data. This function needs us very familiar with
engine parameters, for instance, when idle speed is 800RPM or 750RPM,
coolant operating temperature is between 80～105℃, what are the operating voltage and time of each sensor and actuator?
Special Functions:
More special function will be found in different vehicle models.
Actuation/Ative/ Components Test:
mainly to judge whether these actuating components of engine are working properly.
Select enter Settings
users can set the language, unit and other system related options:
Languages: select the language. Please tick the needed option from multi-language options on the right.
Contact Information:
Whatsapp: +8618928405957
Live Support: please click 'online chat' at the right bottom.
Email: info@obdsvs.com
skype: mary_obdsvs; judie_obdsvs; amy_obdsvs
Shipping Warranty:
We usually ship goods By DHL and China post.
DHL: 3-5 days
If you want ship by UPS, EMS, Fedex,Aramex,
UPS and Fedex: 5-7 days
Aramex and EMS: 10-15 working days （this express can’t ship with battery）
China post: 7- 20 working days. At most 45 days.
If you have not received the goods during the normal time, please contact us for checking the package status timely online or by email.
Quality Problem：
1.Warranty Time： within 7 days after receiving package， Buyer: Submit a complaint(Mail toinfo@obdsvs.com ) and Return the items to Seller's assigned address by DHL or Post. Seller: If can not repair,exchange a new one (Items must be in new condition with original packaging and accessories.) ship cost: Seller
2:within 8-14 days after receiving package: Buyer: Submit a complaint and Return the items to assigned address by DHL or Post for repairing. Seller: If can not repair,exchange a new one (Items must be in new condition with original packaging and accessories.)
Return Ship cost: Buyer, Resend ship cost: Seller
3.within 15 days to 1 year after receiving package. Buyer: Submit a complaint and Return the items to assigned address by DHL or Post for repairing, Ship cost: Buyer
Lost in the delivery:
1.30 days after shipping, Buyer: Submit proof to seller, Seller: Contact carrier to ask for Claimant and arrange another shipment to buyer, Ship Cost: Seller
Customs Problem：
1.30 days after shipping，Buyer: Finish customs clearance when import，Seller: Try to help buyer to finish customs clearance but not responsible on this.
Customs duties or agent fees: Buyer。
Received wrong Items：
1.within 3 days after receiving package。Buyer: Report to Seller,and return the full package in good condition to assigned address by DHL or Post in 3 days. Seller: Arrange shipment for the correct items. Ship cost: Seller
Man-made Damage: such as update machine online, dismantle the equipment, and so on: within 1 year. Buyer: Report to Seller,and return the items for repairing to assigned address by DHL or Post. ship cost: Buyer
Note:
1.Warranty Policy only protects Main parts.Other parts are out of our warranty policy.
2.Before return,please confirm with us. we will give you a shipping address once confirmming the problem. Buyer will be responsible for any risks or costs without our permission.
3.Buyer needs return the items by cheaper DHL or Post, or we can't get them because of restrict Customs Policy.
4.The Warranty Policy fits for all products except some products which state the warranty specially in description.
Warranty Item
Main Unit for Equipment 1 year warrnaty
Machine peripheral equipments and wire No warranty
Car diagnostic laptop 3 months
Data Hard Disk No warranty
Car software No warranty
Consumables No warranty
